ASTM A335/A335M-11

1.1 This specification covers nominal wall and minimum wall seamless ferritic alloy-steel pipe intended for high-temperature service. Pipe ordered to this specification shall be suitable for bending, flanging (vanstoning), and similar forming operations, and for fusion welding. Selection will depend upon design, service conditions, mechanical properties, and high-temperature characteristics.

1.2 Several grades of ferritic steels (see Note 1) are covered. Their compositions are given in Table 1.

Note 1 - Ferritic steels in this specification are defined as low- and intermediate-alloy steels containing up to and including 10 % chromium.

1.3 Supplementary requirements (S1 to S7) of an optional nature are provided. These supplementary requirements call for additional tests to be made, and when desired, shall be so stated in the order together with the number of such tests required.

1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the "M" designation of this specification is specified in the order.

Note 2 - The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as "nominal diameter," "size," and "nominal size."

TABLE 1 Chemical Requirements

Grade	UNS Designa- tionA	Composition, %
		Carbon	Man- ganese	Phos- phorus, max	Sulfur, max	Silicon	Chromium	Molybde- num	Others
P1	K11522	0.10-0.20	0.30-0.80	0.025	0.025	0.10-0.50	. . .	0.44-0.65	. . .
P2	K11547	0.10-0.20	0.30-0.61	0.025	0.025	0.10-0.30	0.50-0.81	0.44-0.65	. . .
P5	K41545	0.15 max	0.30-0.60	0.025	0.025	0.50 max	4.00-6.00	0.45-0.65	. . .
P5b	K51545	0.15 max	0.30-0.60	0.025	0.025	1.00-2.00	4.00-6.00	0.45-0.65	. . .
P5c	K41245	0.12 max	0.30-0.60	0.025	0.025	0.50 max	4.00-6.00	0.45-0.65	. . .B
P9	S50400	0.15 max	0.30-0.60	0.025	0.025	0.25-1.00	8.00-10.00	0.90-1.10	. . .
P11	K11597	0.05-0.15	0.30-0.60	0.025	0.025	0.50-1.00	1.00-1.50	0.44-0.65	. . .
P12	K11562	0.05-0.15	0.30-0.61	0.025	0.025	0.50 max	0.80-1.25	0.44-0.65	. . .
More ASTM standard pdf ASTM D3514/D3514M-16 Standard Test Method for Pilling Resistance and Other Related Surface Changes of Textile Fabrics: Elastomeric Pad $24.00 $48.00 Add to Cart ASTM F1762-14 Standard Test Method for Determining the Effects of Atmospheric Pressure Variation on a Membrane Switch (Withdrawn 2023) $30.00 $60.00 Add to Cart ASTM F1973-99 Standard Specification for Factory Assebled Anodeless Risers and Transition Fittings in Polyethylene (PE) Fuel Gas Distribution Systems $25.00 $50.00 Add to Cart ASTM D5089-95(2014) Standard Test Method for Velocity Measurements of Water in Open Channels with Electromagnetic Current Meters (Withdrawn 2023) $30.00 $60.00 Add to Cart