• ASTM D5967-09

ASTM D5967-09

Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine

ASTM International, 04/15/2009

Publisher: ASTM

File Format: PDF

$33.00$67.00


Published:15/04/2009

Pages:20

File Size:1 file , 380 KB

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including viscosity increase and soot concentrations (loading). This test method is commonly referred to as the Mack T-8.

1.2 This test method also provides the procedure for running an extended length T-8 test, which is commonly referred to as the T-8E and an abbreviated length test, which is commonly referred to as T-8A. The procedures for the T-8E and the T-8A are identical to the T-8 with the exception of the items specifically listed in Annex A8 and Annex A9 respectively. Additionally, the procedure modifications listed in Annex A8 and Annex A9 refer to the corresponding section of the T-8 procedure.

1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3.1 Exceptions - Where there is no direct SI equivalent such as the units for screw threads, National Pipe Threads/diameters, tubing size, sole source equipment suppliers, and oil consumption in grams per kilowatthour.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A6 for specific safety precautions.

1.5 A Table of Contents follows:

More ASTM standard pdf

ASTM C867-94(2014)

ASTM C867-94(2014)

Standard Test Method for Soluble Sulfate in Ceramic Whiteware Clays (Photometric Method)

$28.00 $56.00

ASTM C927-80(1999)

ASTM C927-80(1999)

Standard Test Method for Lead and Cadmium Extracted from the Lip and Rim Area of Glass Tumblers Externally Decorated with Ceramic Glass Enamels

$25.00 $50.00

ASTM D4195-08(2014)

ASTM D4195-08(2014)

Standard Guide for Water Analysis for Reverse Osmosis and Nanofiltration Application (Withdrawn 2023)

$30.00 $60.00

ASTM D210-81a(1999)

ASTM D210-81a(1999)

Standard Specification for Bone Black Pigment

$25.00 $50.00

Scope 1
Referenced Documents 2
Terminology 3
Summary of Test Method 4
Significance and Use 5
Apparatus 6
General Description 6.1
The Test Engine 6.2
Mack Test Engine 6.2.1
Engine Cooling System 6.2.2
Engine Oil System 6.2.3
Auxiliary Oil System 6.2.4
Crankcase Aspiration 6.2.5
Blowby Meter 6.2.6
Air Supply and Filtration 6.2.7
Fuel Supply 6.2.8
Intake Manifold Temperature Control 6.2.9
Engine Fluids 7
Test Oil 7.1
Test Fuel 7.2
Engine Coolant 7.3
Cleaning Materials 7.4
Preparation of Apparatus at Rebuild 8
Cleaning of Parts 8.1
Valves, Seats, Guides, and Springs 8.2
Cylinder Liner, Piston, and Piston Ring Assembly 8.3
Injectors and Injection Pump 8.4
Assembly Instructions 8.5
Measurements 8.6
Laboratory and Engine Test Stand Calibration/Non-Reference
Requirements
9
Calibration Frequency 9.1
Calibration Reference Oils 9.2
Test Numbering 9.3
New Laboratories and New Test Stands 9.4
Calibrated Laboratories and Test Stands 9.5
Calibration Test Acceptance 9.6
Failing Calibration Tests 9.7
Non-Reference Oil Test Requirements 9.8
Procedure 10
Pretest Procedure 10.1
Engine Start-Up 10.2
Engine Shutdown 10.3
Test Cycle 10.4
Oil Addition/Drain 10.5
Oil Samples 10.6
Oil Consumption Calculations 10.7
Fuel Samples 10.8
Periodic Measurements 10.9
Blowby 10.10
Centrifugal Oil Filter Mass Gain 10.11
Oil Filter ΔP Calculation 10.12
Post Test 10.13